Automatic Hand Sanitizer Dispenser with COVID19

$30-250 USD

Cerrado

Publicado

hace alrededor de 4 años

$30-250 USD

Pagado a la entrega

In this project, we will build an Auto Hand Sanitizer Dispenser with an LCD which also shows the live count of Coronavirus cases. This project will use ESP32, Ultrasonic Sensor, 16x2 LCD Module, Water pump, and Hand Sanitizer. We are using Esri’s API Explorer to get the live data of Covid19 infected people. An ultrasonic sensor is used to check the presence of hands below the outlet of the sanitizer machine. It will continuously calculate the distance between the sanitizer outlet and itself and tells the ESP to turn on the pump whenever the distance is less than 15cm to push the sanitizer out. ESP32 is used as the main controller, it is a Wi-Fi module that can easily connect to the internet. We previously used it to build many IoT based projects using ESP32.

Embedded Systems

ID del proyecto: 24838884

Información sobre el proyecto

19 propuestas

Proyecto remoto

Activo hace 4 años

¿Buscas ganar dinero?

Dirección de email

Beneficios de presentar ofertas en Freelancer

Fija tu plazo y presupuesto

Cobra por tu trabajo

Describe tu propuesta

Es gratis registrarse y presentar ofertas en los trabajos

19 freelancers están ofertando un promedio de $166 USD por este trabajo

@hemedmechanical

Hello, you should use OLED SSD1306 display in place of 16x2 which is an obsolete one OLED display runs on very little power hence more energy efficient i will program your system to auto open/close valve, sending request to your API to fetch data of the number of the victims as well hit me on chat for more please i have very deep experience with ESP32

$200 USD en 7 días

5,0

(8 comentarios)

3,9

@mazeemsk

Hi, I am an Electrical, Electronics and Embedded Engineer. A PCB Designer, Arduino/Raspberry Pi, ESP32, ESP8266 and internet of things expert. I read through the job description very carefully and I am absolutely sure that I can do the project very well. I have worked on similar projects to what you are looking for, and I am confident I can exceed your expectations. I can achieve the results that you are asking for.I can complete your project on time and within your budget. Thanks

$100 USD en 3 días

5,0

(1 comentario)

2,1

@Agraharianubhav

Dear client, Your posted job is very suitable for me, I did same before. So I will not take more time in your project. Sir I can provide you only code and circuit diagram, because the transportation is stoped due to Covid-19 lockdown. My profession- I m working in a home automation company talkingthings as a technical lead. I have expertise in IoT, embaded system, Arduino, Avr and many other MCU. We can discuss more about your project in chat box. If you interested to work with me. Waiting for your response... Regards, Anubhav Agrahari

$56 USD en 1 día

0,0

(0 comentarios)

0,0

@creandoTec

Hi! I'm a mexican electronics engineer. I have experience working with esp32, ultrasound sensor and LCD. I can do your project, there is no doubt. But, are you going to need the PCB design too? Which kind of LCD module are you going to use, I mean, an I2C board, or you will wire all the LCD modules to the ESP32? Did you alredy choose the ultrasound sensor and the water pump? I mean, I'll need to know all that info because to design the power circuit for the water pump, and make the voltage translation if the ultrasound works at 5V, and that kind of stuffs. Regards

$230 USD en 7 días

0,0

(0 comentarios)

0,0

@hamzazayyad

Hello I have 15 years experience in the embedded systems and interest in your project...... Thank you

$228 USD en 3 días

0,0

(0 comentarios)

0,0

@sossey

Hello, I have a good experience in ESP32 MCU programming using Arduino IDE or ESP-IDF , i have just read your project requirements and i am very interested to develop code for your Automatic Hand Sanitizer. We can discuss more details over chat. Best regards.

$50 USD en 3 días

0,0

(0 comentarios)

0,0

@AnantChaudhari1

Hi, I can help you develop this idea into reality. I have experience working with ESp8266 and other embedded platforms

$200 USD en 7 días

0,0

(0 comentarios)

0,0

@Sanjaysingh2018

your project is ready as I have built a similar device and selling in india. it is esp32 wroom 32 based. used ultrasonic sensor to detect the hand and dispense the solution . drop me message I can share you my device photo. hardly it would take an hour if u are looking for firmware.

$111 USD en 1 día

5,0

(1 comentario)

0,0

@sagradoamicus

Hi I am experienced embedded system developer with more than 15 years of experience. I can do it for you. I have worked on ESP32 and ultrasonic sensors a number of times before and would like to discuss it in further detail Regards Ali

$250 USD en 4 días

0,0

(0 comentarios)

0,0

@ajayk3289

hi I am Ajay , I have good experience in Arduino and esp development , I worked on a pet food dispenser based on PIR sensor , the same technology will be modified and can be work on this project and the data integration with lcd display will be done as early as possible and deliver it to you in maximum of 100 hours from date of project acceptance I have all material except pump that can just added to relay so I will start work as early as possible

$194 USD en 4 días

0,0

(0 comentarios)

0,0

@itsum

I can do this. Relevant Skills and Experience I have vast knowledge of embedded systems and sensors like 8051, AVR, Arduino, Raspberry pi, ARM7 etc.

$56 USD en 3 días

0,0

(0 comentarios)

0,0

@mlarun55

I have lot of experience in esp32 and i am a embedded developer from last 10 years so I can do it perfectly .

$250 USD en 5 días

0,0

(0 comentarios)

0,0

@rtdxinc

That's a quick project, I can program your esp so that it detects any object on the ultrasonic sensor and starts up the pump using the relay. I been working as an IOT Developer for quite a while now. Would love to hear back!

$178 USD en 3 días

0,0

(0 comentarios)

0,0

@JonethanJ

Dear Friend We are a Beijing China-based company and offer from design to mass production services to our customers. We provide turn-key solutions. We can help you to design and manufacture your product. Please feel free contact me to discuss more about your project. Best Regards Jonethan

$140 USD en 7 días

0,0

(0 comentarios)

0,0

@rohandey87

Hi, A very interesting and a need of the hour product idea I must say. I am from India. I will be able to help you design your product. I have over 11 years of experience in Embedded Systems. I have also built many projects with the ESP32 chip. Please have a look at my profile. Please get back to me and then we can discuss further with your requirement. Thanks, Rohan Dey

$200 USD en 7 días