Electronic developer

Hi I am experienced electronics engineer with more than 11 years of experience. I can do it for you. I have worked on a number of projects before. Please share the further details of the project. I am waiting for your reply to start Regards

Hello, I have read MAX11645 datasheet. it's i2C based 12 Bits ADC right? Personally I never used that chips. But I have 8 years experience dealing with both hardware & firmware development especially in Microcontroller. I'm familiar with I2C used in many chips, including ATMEGA. let me know the detail task of this project. I can do prototyping including PCB design & firmware development. Let's discuss the details over chat. Best Regards, Rijal

Hi. I'm an electronics engineer with tons of experience including Arduino and I2C communication to all kinds of devices like ADCs and can do the job. And I speak Russian if you wish. Best regards, Denis

Hi, I have been working on embedded systems for more than ten years. I have developed similar firmware like your job. If you like, we can discuss details.

would be glad to assist you with the project. have worked so many mega, tiny arm projects. this particular instance is an arc chip with i2c interface. should be straight forward.

Hello! need to meet you! I'm Engineer. I'd worked with MAX11645 it is . it's analog-to-digital converters (ADCs) of 12 Bits and I2C. I've experiences in electronic design, Arduino. Atmel. Pic Microchips Family, pic 8, 16 & 32 bit, raspberry pi. matlab. python, C/C++, RTO system, mplab, xc8, xc16, xc32. CCS . I've 5+ years experiences im design the robot. electronic and PCB design . Send me a message to discuss more about it.

Hello! Nice to meet you! I have read your project carefully. I am very interested in your project. I am a Microelectronics and Automation engineering expert. I have a lot of experience on ARM, FPGA, DSP, Arduino, Raspberry, PLC, PIC, ATMega and so on. And I can code the Python, C/C++. I can do help you. I hope to cooperate with you. Tell me your opinion. My regards.

Hello, Hope you are doing well! Thanks for sharing your project requirement with us. It will be my great pleasure to work on your project. I have checked your requirement, yes I can do it. I have right skills to work on this assignment. My work area includes Computer Software, Embedded Systems (Hardware & Software), Analog & Digital Circuit design, PCB design services etc. My Capabilities: PCB & Schematic: Cadsoft Eagle, Altium Designer 15, Kicad, Proteus. Micrcontroller Arch.: STM32 F0/1/2/4, AVR, PIC16/18/24/32, ARM7, ARM Cortex M0/M3, Arduino Boards, STM Discovery Kits, Raspberry Pi Boards. Wireless Module: ESP, Nordic Modules, RFID/MiFARE, GSM/GPRS(SIMCOM, Telit, Quectel etc),Bluetooth etc. Programming Languages : C, Python, C# .Net, VC++, PHP etc. Programming tools & IDE: Arduino,STM32 Cube IDE,Keil-MDK, AVR Studio, MPLAB X, Visual Studio 2017, Mikroelectronika Mcu Sillicon Vendors: NXP, Atmel, ST Microelectronics, Microchip etc. I will complete the work as per requirement and within suggested time frame. Your work will be kept upto you, it will not be used with other client.

Hello, I can help you with ATmega programming for Max11645. I have coded for other MAX converter (MAX1416) and Atmel mcu. Max11645 is different device, but it should not be problem to make code for that. I you are interested I would get Max11645 converter ic so I can test it as well. What ATmega mcu you need to use? By the way, Max11645 is 3.3V device, probably some voltage level conversion is needed on schematic with I2C pins if ATmega runs at 5V. Max11644 works with 5V directly.

NOTE: I could do this project for around 150-200$USD. The platform doesnt allow me to go below 250. TL;DR: Just as a proof of commitment, I could give you a proof of concept for what you required, in a couple days, no strings attached, so that you can take a look at my work without taking any risk. Read further, if interested. Good day. I have plenty of experience working with MCU-based embedded systems. I've worked at Freescale Semiconductors for half a decade as an engineer. I've worked with several arm-based microcontrollers (NXP, Atmel (now Microchip) and STs families) and, lately, with the esp8266 and esp32 family of microcontrollers, either with or without an RTOS. I'd need more information regarding the exact specifications of your project, as well as your expected timetable. However, I can say the time stated is more than enough for finishing what I think you are asking, and for having a long enough testing phase. Regarding payment,of course, none is required before a proof of work (firmware, and related documentation). I'd find quite useful for the both of us, if you'd find the time to talk a bit further regarding your project's requirements.

I hold master degree in instrument tech and having about 35 years of expertise in real time embedded hardware and software applications. I worked with many ADCs and I2C devices.

I have good programming skills in Arduino platform, AVR based ICs and ESP8266 based boards and have 9 years of professional experience.. I have expert level knowledge on C language especially in developing drivers for I2C, SPI, UART interfaces and in developing code logic for interfacing sensors and actuators for projects related to IOT, robotics etc. I am interested in undertaking various Arduino projects with complexities ranging from beginners to advanced. I have decided to dedicate my free time to work with such projects from good clients and to maintain a long term and healthy relationship with them. Please contact me if you are interested.