Find Jobs
Hire Freelancers

Design LTE hardware from Base band Unit, EnodeB and Transmitters

min $5000 USD

Cerrado
Publicado hace más de 10 años

min $5000 USD

Pagado a la entrega
We are looking at producing a 10W LTE to meat the requirements of release 11. consideration for release 12- 15 should be provided. design with an integrated EnodeB and BBU design objectives - 1) small footprint 25cx X 25cm to fit inside a pole - reasonable vertical height available for design 2) reliability under extreme conditions - high heat, limited air flow, high humidity etc. 3) LTE EnodeB and BBU unit should be of same footprint and possible Plugged together? top to bottom. 4) TDD capability a primary priority (frequency / band coverage should be "Chip" dependant ie base unit supports any frequency chip installed. 5) 40Mhz, in 20Mhz blocks (ideally 60Mhz perhaps as a field implemented optional upgrade?) 6) option for a FDD EnodeB to connect to same BBU - ie support both TDD and FDD from same transmitter location. 7) as low power consumption as possible.(note no room for any equipment at base of Pole ? 8) Transmitter areal plugged external either Omni- areal or Directional, high gain 9) transmitters should be designed for maximum gain at 10w or 15w of power - knowledge of DB output etc required. 10) Drawings and IP will be transferred to purchaser (me). 11) Time to design a issue? estimate should be provided. we are planning to manufacture units and want to "Buy" the working design. We are not available for a per unit Royalty will also consider bidders who bid on certain parts ie EnodeB, BBU or transmitters separately
ID del proyecto: 4726977

Información sobre el proyecto

6 propuestas
Proyecto remoto
Activo hace 11 años

¿Buscas ganar dinero?

Beneficios de presentar ofertas en Freelancer

Fija tu plazo y presupuesto
Cobra por tu trabajo
Describe tu propuesta
Es gratis registrarse y presentar ofertas en los trabajos
6 freelancers están ofertando un promedio de $440.910 USD por este trabajo
Avatar del usuario
hi, i am an electrical engineer and an embedded system designer. i can help you with this project.
$515.463 USD en 250 días
4,8 (54 comentarios)
6,7
6,7
Avatar del usuario
Dear Sir, I'm 15 year experienced Electronics Engineer whose working area is directly related to your project. I have designed several system which is related to your project. I have high level experience about hardware design, analog design, embedded system, microcontroller, power electronics, system simulation, digital motor control. Examples related to your project are attached. It shows my ability to make your project. If you investigate example, you will see that I have strong background similar to your projects. Project lists which I have made until now is attached also. We can determine budget by discussing details of your project. I’m open to work with amount which you can pay. Any questions, you can ask me. The way which will be used to implement is such as: - My profile is below. It shows every issues related to your project. Please evaluate it carefully. If you do it, you will see that I'm ideal candidate who can make your project without any problem. I will wait for being started contract. Regards. Metin Dear Sir, We are Reserach and Development company whose working area are : -Digital Motor Control -Analog Design -Electronic Design -Power Electronics -PCB design -Embedded system -Matlab -Simulation of hardware For each concept descriptions are as follows: Digital Motor Control: -3-phase induction motor vector control drive -Flux estimation algoritm generation -DSP(TMS320) implementation on motor drive -Low speed application -Torque and speed loop generation -Control algoritms Analog design -Low power distribution -Noissless special opamp based analog circuits -Analog filters -Orcad simulation of several circuits Electronic Design -RF transmitter and receiver -Bluetooh reader and transmitter -Magnetic reader Power Electronics -Implementation motor drive -AC/DC converter -DC-DC converter -Battery charger -Solar inverter -Renewable Energy simulations -Uninterruptle power supplies PCB design -Schematic design by Altium -PCB design by Altium -Power board design -SMPS board design Embedded system -PIC18,PIC24,PIC30 and dsPIC applications -Ardino -MSP430 -Atmel -DSP(Texas Instruments) -Renesas Matlab -Power Electronics simulation -Motor drive -Wind Energy -Solar Energy -Control applications Simulation of Hardware -Orcad Simulation(TI,National, Linear Tech, Maxim libraries) -LTI -National -Matlab Very important Note: References attached. Please look excel file to see projects which we made until now! Metin
$5.555 USD en 3 días
4,6 (15 comentarios)
4,8
4,8
Avatar del usuario
Hi working on a prototype development company located in Spain electronics, we can implement your project. with all the details you provided.
$5.000 USD en 30 días
0,0 (0 comentarios)
0,0
0,0
Avatar del usuario
Ready to supply top quality solution.
$2.000.000 USD en 365 días
0,0 (0 comentarios)
0,0
0,0
Avatar del usuario
Please check PM for detail, Thanks.
$8.888 USD en 60 días
0,0 (0 comentarios)
0,0
0,0
Avatar del usuario
Hello, I can do it.
$111.111 USD en 99 días
0,0 (0 comentarios)
0,0
0,0

Sobre este cliente

Bandera de UNITED KINGDOM
Epping, United Kingdom
0,0
0
Forma de pago verificada
Miembro desde mar 10, 2013

Verificación del cliente

¡Gracias! Te hemos enviado un enlace para reclamar tu crédito gratuito.
Algo salió mal al enviar tu correo electrónico. Por favor, intenta de nuevo.
Usuarios registrados Total de empleos publicados
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Cargando visualización previa
Permiso concedido para Geolocalización.
Tu sesión de acceso ha expirado y has sido desconectado. Por favor, inica sesión nuevamente.